please dont rip this site

Toner Transfer PCB Etch Resist

The use of pressure / heat / chemicals to transfer toner printed on various different papers by a laser printer or copier onto the target. This is often used to make PCB's resist layers, however: "I found that toner transfer works on painted surfaces. To improve the appearance of my bots, I give the top side of the finished pcb a light coat of Krylon flat white and then toner transfer. Looks great." Thanks to the Yahoo "Homebrew PCBs" group for much of the information collected here.

ON THIS PAGE:

Toner Transfer Media

Toner Transfer Methods

The 'Press-N-Peel' version generally works better, but costs more, than the 'Press-N-Soak' version. You can get both kinds from Electronics Express:
http://www.elexp.com Press and re-melt works very well if you are careful not to smear.
http://www.elexp.com/pro_npb5.htm (as of 2010/05/13)

Process:

Cleaning the PCB stock is critical. Scrubbing with scotch brite pads, bar keepers friend or other light abrasive cleaners is recommended. Avoid anything with oils, "conditioners", or that leaves any sort of film.

Having said that, it has been reported that CitraSolv cleaner (a very effective degreaser and cleaner based on d-Limonene from citrus rind) is an effective toner solvent and works nicely as an surface prep for PCBs. It does leave a thin film, but that film acts to bind the toner to the PCB. Richard Dheiliger reports that Laquer Thinner also leaves a "haze" that appears to help the transfer process.

Dustin reports that after the main scrub and clean with Glass Cook Top cleaner, a rinse in Tarn-X also helps so that may be a good way to "fix" any otherwise good abrasive cleaners which would otherwise leave behind a film.

Pre-etching the PCB stock can help the toner adhear. Some people wipe the copper with Ferric Chloride to "rust" the surface and then just leave it on, others dip the board and clean it off. This provides a rough surface that improves the toners ability to grab onto the copper.

Pre-heating the PCB stock in an oven (e.g. 350'F for 3 minutes) helps the toner stick. Be careful when laying down the paper as the toner will stick and smear if the paper is moved.

Printing When printing, keep in mind that the printers / software may not produce a printout that is /exactly/ the correct size. The traces may be "stretched" or warped in the x or y axis. It's good to have a PCB program that allows fine scaling of the printed size in either dimension. The alignment of the printer can also be adjusted by a competent service tech. This issue can, in extreme cases, cause individual components to fit poorly but most often the error is small enough that it only becomes apparent when you try to CNC drill the holes; when one side of the board is lined up in the mill, the other side will be off just far enough to cause the machine to drill outside the pad.

If you media is very thin or curly (e.g. magazine or parchment paper) or hugly expensive, you may wish to tape it to a regular sheet of paper with kapton tape along the leading edge. You can print the pattern once on paper, then use that as a guide to tap the media in place over the printed area, and feed the same stock again to ensure it will print exactly where expected.

Transfer

Methods of Transfer by applying Heat and Pressure:

Chemical Transfer Methods

Super Glue: If using Parchment Paper or other silicone coated stock (see above) then you can transfer without heat and only moderate pressure by wiping a thin layer of super glue onto the metal, and immediately pressing the baking paper with printed design onto the metal surface. The toner will stick to the wet super glued metal, but the paper will lift off after the glue has dried.

Rod^ says:

"Too much glue, and or too dark a toner printout will cause the toner to muddy up, so use a little glue on a Q Tip cotton swob. If you experiment, within a few minutes you can hit upon the correct, light print, and light coating of glue. I go for more of a grey printout, rather than black. Do not wipe the glue onto the baking paper, wipe it onto the metal....thin wipe with no excess puddles.

Do not wait for the glue to dry, but apply your design immediately. Burnish with the back of the finger nail, or a bone burnisher, etc., and no need to press too hard. Watch the design leave the paper using microscope or magnifier. When you sense the toner has transferred, you may wait a few minutes to ensure the glue has set. If things go wrong, a quick wipe with acetone cleans the metal down for a second try. If you get partial transfer, your glue may have dried too soon, or maybe you need a little more glue. Use the thin watery super glue, and make sure it is like water, it has a shelf life and sometimes it is already hard or thick from too long on the shelf at the store where you bought it. It is about 20 times cheaper by the once compared with 1 gram at the store. Keep it in the freezer for longer shelf life of about 6 months."

Blender Pen: Jesse Willis says:  "What I did was swing by my local art store and pick up an Eberhard Faber Design Art Marker, Broad Nib 311 Colorless Blender (only about $2 US). With this, you simply photocopy the circuit you wish, and then lay the photocopy face down on the PCB. Run the marker over the back of the photocopy, and the image transfers to the copper." If anyone has a source for these pens, or has tried another brand of Colorless Blender Pen, please let us know?

Acetone / Alchol mixture: simpletronic documented the use of a mixture of Ethyle Alcohol (96% pure) and Acetone (or Toluene or Xylene) to soften the tonor and allow it to be fully transfered to the blank. He applies a mixture of 3 parts Acetone and 8 parts Ethyl Alcohol , or 4 parts denatured alcohol to 1 part Xylene, to the blank, then drops the paper, toner side down over that. After waiting 5 - 10 seconds, direct pressure is applied and then 2 minutes are allowed for the solvents to be "volatilized". After that the paper is removed by soaking.
http://www.instructables.com/id/Heatless-cold-Toner-Transfer-for-PCB-Making/?ALLSTEPS
 
Others report success with 70% Isopropyl alcohol with acetone (3/8) or 2/3 methylated spirit and 1/3 of automotive acrylic lacquer thinner (mainly acetone)

Paper Removal:

Re-Melt: Re-heating the board after paper removal will allow the toner to re-flow and fill any tiny holes or cracks that would otherwise allow the etchant to penetrate the resist.

Touch-up: Check for traces that are broken or large pads / fills that haven't filled in well. Some laser printers have a difficult time filling in large areas. Using crosshatched fills rather than solid may avoid this issue. Correct these errors with a fine tip Black Sharpie^ (only the black seems to hold up).

Check for smudges, smears, or just places where the toner has spread too much and closed in the gap between traces or pads. Use a needle or narrow tip knife to scrape away the toner and expose the bare copper underneath.

Etching the board is the final step. See: PCB Etch, PCB Echant, Printed Circuit Board fabrication

Removing the toner: Acetone (e.g. Nail Polish remover) seems to be the only thing that takes toner off quickly and cleanly. It's a nasty chemical and shouldn't be used in a closed space. You can put the PCB and some Acetone in a ziploc bag, then soak it while rubbing the board through the plastic to keep your exposure to a minimum.

It has been reported that CitraSolv cleaner (a very effective degreaser and cleaner based on d-Limonene from citrus rind) is an effective toner solvent, but this has not been extensivly tested.

Advantages:

Disadvantages:

Links:

See also:

Laser printers made by the "Brother" brand apparently use a toner formulation that melts at a much higher temperature than others; about 187C (370F). As a result, it can be harder to transfer the toner to the PCB. Also, the toner used in older Brother printers, such as the HL-2400CN, appear to have an oily consistency which prevents adhesion of the toner to the PCB. Newer Brothers, such as the MFC-9420CN work ok as long as a higher transfer temperature is maintained. +

HP and Lexmark toner melts at 170 - 180°C  (338 - 356°F)

Marion D. Kitchens says:

I have had good results as follows: Using a plastic film intended for the purpose, print a negative image with a laser printer. This will iron onto clean copper nicely of you are careful. I find it works better if I heat the copper board on the iron, and then roll the film sheet onto the moderately hot copper. I use a roller from the photo lab, and roll with light pressure. Too much pressure will smear the toner. I have been able to get copper traces between the 0.10 pins of IC's this way. Good luck...  

Comments:

Questions:


file: /Techref/tonertransfer.htm, 27KB, , updated: 2020/7/23 21:46, local time: 2024/10/4 07:15,
TOP NEW HELP FIND: 
44.222.134.250:LOG IN
©2024 PLEASE DON'T RIP! THIS SITE CLOSES OCT 28, 2024 SO LONG AND THANKS FOR ALL THE FISH!

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://www.sxlist.com/techref/tonertransfer.htm"> Toner Transfer, press-n-peel,PCB Etch,Etch PCB</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

 

Welcome to sxlist.com!


Site supported by
sales, advertizing,
& kind contributors
just like you!

Please don't rip/copy
(here's why

Copies of the site on CD
are available at minimal cost.
 

Welcome to www.sxlist.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .