please dont rip this site

PICList Project

John Andrews' PICos

John Andrews of Microchip has contributed his code for makeing the 17C756 into a very nice little multi-purpose IO device with an easy serial command interface. You can monitor and change registers, port pins, A2D, Capture channels and PWM, send and recieve data to / from I2C and EEPROM all with text commands from USART1.

Source

Documentation

See the listings as well.

Run Time Communications:
	Connect to USART1
	ASCII Terminal settings
		Baud:           9600
		Data bits:      8
		Parity:         none
		Stop bits:		1
		Flow Control:   none

The following Commands are available in PICos 1.04

COMMAND                 ACTION
--------------          -------------------------------
<ENTER>                 Null command (should see prompt "PICos>")

MSG:str<ENTER>          Display the string message on USART1
VER<ENTER>              Display PICos version

ANn<ENTER>              Read A/D channel n (n = 0 - 11, demo board requires n = 0 - 3)

T<ENTER>                Read Thermister (on AN4)

REGx:x=x<ENTER>         Write a hexidecimal value to bank:register
REGx:x<ENTER>           Read value in bank:register and display in hexidecimal format

PORTDD=n<ENTER>         Write decimal value to PORTD (n = 0 - 255)
PORTDD<ENTER>           Read value on PORTD and display in decimal format (n = 0 - 255)
PORTDX=n<ENTER>         Write hexidecimal value to PORTD (n = 00h - FFh)
PORTDX<ENTER>           Read value on PORTD and display in hexidecimal format (n = 00h - FFh)
PORTD=n<ENTER>          Write hexidecimal value to PORTD (n = 00h - FFh)
PORTD<ENTER>            Read value on PORTD and display in hexidecimal format (n = 00h - FFh)

PWM1=n<ENTER>           Write PWM1 Duty cycle as a percentage 'n' of the period (n = 0 - 100)
PWM2=n<ENTER>           Write PWM2 Duty cycle as a percentage 'n' of the period (n = 0 - 100)
PWM1  <ENTER>           Read PWM1 Duty cycle as a percentage of the period (n = 0 - 100)
PWM2  <ENTER>           Read PWM2 Duty cycle as a percentage of the period (n = 0 - 100)
PWM2+=n<ENTER>          Increase PWM2 Duty cycle by percentage 'n' of the period (n = 0 - 100)
PWM2-=n<ENTER>          Decrease PWM2 Duty cycle by percentage 'n' of the period (n = 0 - 100)

CAPn<ENTER>		Measure capture value on channel n = 1 or 2

I2CADDR=n<ENTER>        Write value n to the I2C slave address (n = 00h - 7Fh)
I2CADDR<ENTER>          Read I2C slave address (n = 00h - 7Fh)
I2Cn<ENTER>             Read byte at I2C address (n = 00h - 7Fh)
I2Cn=x<ENTER>           Write value x at I2C address (n = 00h - 7Fh, x = 00h - FFh)
EEn<ENTER>              Read byte at EEPROM address n (n = 00h - FFh)
EEn=x<ENTER>            Write byte with value x at EEPROM address n (n = 00h - FFh, x = 00h - FFh)
S@EEn<ENTER>            Read string starting at EEPROM address n (n = 00h - FFh)
S@EEn=str<ENTER>        Write string 'str' starting at EEPROM address n (n = 00h - FFh, str = a string upto 40 characters)
I2Cn:str<ENTER>         Write the PICos command 'str' to I2C slave address 'n' (n = 00h - 7Fh, str = PICos command)
I2Cn:<ENTER>         	Read a string from I2C slave address 'n' (n = 00h - 7Fh)


file: /Techref/piclist/andrewspicos/index.htm, 4KB, , updated: 2008/3/29 19:37, local time: 2024/3/18 20:41,
TOP NEW HELP FIND: 
34.230.84.106:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://www.sxlist.com/techref/piclist/andrewspicos/index.htm"> PICList Project </A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

 

Welcome to sxlist.com!


Site supported by
sales, advertizing,
& kind contributors
just like you!

Please don't rip/copy
(here's why

Copies of the site on CD
are available at minimal cost.
 

Welcome to www.sxlist.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .