; *****************************************************************************************
; Copyright © [01/26/1999] Scenix Semiconductor, Inc. All rights reserved.
;
; Scenix Semiconductor, Inc. assumes no responsibility or liability for
; the use of this [product, application, software, any of these products].
; Scenix Semiconductor conveys no license, implicitly or otherwise, under
; any intellectual property rights.
; Information contained in this publication regarding (e.g.: application,
; implementation) and the like is intended through suggestion only and may
; be superseded by updates. Scenix Semiconductor makes no representation
; or warranties with respect to the accuracy or use of these information,
; or infringement of patents arising from such use or otherwise.
;*****************************************************************************************
; SX Single I2C Multi-Master demo.
;
; Filename: i2cmm.src
;
; Author: Chris Fogelklou and Bruce Wilson
; Applications Engineers
; Scenix Semiconductor Inc.
;
; Revision: 1.06b (preliminary, for review)
;
; Part: SX28AC datecode 9929AA
; Freq: 50Mhz
; Compiled using Parallax SXKey28L
; Parallax SXKey52
; SASM
;
; Date Written: Aug 23,1999
;
; Last Revised: June 26,2000
;
; Introduction:
; The I2C multi-master Virtual Peripheral™ has been written to enable the user to simply and
; easily operate the SX as an I2C master in multi-master mode. A multi-master I2C bus is when
; more than one master may initiate an I2C transfer on the I2C-bus. Arbitration is used to
; determine whether or not a master is able to use the bus at any given time.
;
; Program Description:
; This program is a very straight forward I2C multi-master demo, which uses the I2C multi-master
; VP as a foundation. This program relies on two aspects for correct multi-master operation. The
; first is an arbitration algorithm which executes every ISR. This arbitration algorithm is used to
; detect when a master may communicate on the bus, or if it must first wait for another master to
; finish. The second aspect which is important for correct operation of the I2C specification on
; the SX, is keeping a defined duration of the start-bit between masters. This ensures that a start
; may always be detected and that each SX master on the bus may synchronize their I2C clocks before
; beginning a transmission.
;
; To run this demo on the Scenix demo board all you need to do is ensure that the
; scl and sda pins, and that the slave address is set correctly. For pin and port setup, refer to
; the documentation for the demo board you are using (pdf-document)
; To read from the onboard EEPROM on the:
; The slave address for the EEPROM is $A0 for both the boards.
;
; If you run the programs in debug mode you will see the data contained in the EEPROM being read
; into the last RAM bank. You can also see the text read and the slave address beeing read from
; in a watch window. Your setup should be as follows:
;
; 4.7k
; VCC x--/\/\/\--------x
; 4.7k |
; VCC x--/\/\/\---x |
; | |
; | | SCL
; SCL ------------x------------------x-------- SCL
; SX 1 | SDA | SX 2
; SDA -----------------x-----------------x---- SDA
; | |
; | |
; SCL SDA
; EEPROM (24LC16B)
;
; The pin definitions on either SX can be easily changed. However, you are restricted to use pin
; 0 and 1 on the port you have assgned for I2C, but you are allowed to switch the SDA and SCL pins.
; It is also recommended that for testing purposes leds be connected to pins RC.0, RC.1 and RC.2. These can
; be used to verify correct operation of the multi-master system.
;
; Once both SX devices have been programmed they will read whatever data is stored in the first bank of the EEPROM
; until a null is found, this data will be written into bank 7 of the SX. Run in debug mode to see the data.
; Since each SX will be trying to do this at the same time, arbitration is used. The SX masters
; will wait until the bus is idle, or a start bit is being put onto the bus. In Either of these cases the master
; will begin transmission. Whichever master pulls the SDA line low first will now win the arbitration procedure.
; The master which loses arbitration will now wait a random length of time
; and then try again. This time that the master waits may need to be adjusted to suit your application. Since
; the way arbitration is detected is by the setting of a flag within the ISR, this allows the user to choose what
; action to take once loss of arbitration is detected. At present the master simply waits up to 85 I2C clock
; cycles before retrying the transmission. The length of this wait is totally dependant on the maximum length
; of any operation to take place on the I2C-bus. It would be unwise to have a timout period of as little as
; 50 clocks, if a master requires a 255 char string read from the EEPROM. It would be also possible to add more
; sophistication to the restart of a transmission whereby it may simply be continued from when arbitration was
; lost.
; Depending on the speed you wish to operate the I2C-bus at it may be necissary to change the pull-up resistor
; values. It is suggested that you refer to the I2C-bus specification pg. 40. This specificaiton is freely
; available at the Philips web site and has some good information on implementing the I2C specification.
;
; I2C Multi-Master VP requirements:
; - 1 RAM bank for I2C MultiMaster variables
; - 1 RAM bank for I2C MultiMaster string read from slave
; - 300 Bytes of Program memory
; - Up to 86 instruction cycles every ISR
;
; Interface Pins:
;
; i2cmmPort ra
; scl 1
; sda 0
;
; i2cmmGreenLed equ rc.2
; i2cmmRedLed2 equ rc.1
; i2cmmRedLed1 equ rc.0
;
;
; Revision History:
; 1.0 Core I2C state machine implemented by Chris Fogelklou
; 1.01 Documentation and code revised and updated by Bruce Wilson
; 1.02 Improved multi-master functionality and tested on the Scenix I2C/UART board
; 1.03 Modified code for SASM assembler and SX52 compatibility
; 1.04 Detection of NACK added to mainline code to avoid continuing a transmission even
; when the slave did not respond. This also solved a known bug, whereby loss of
; arbitration may sometimes not be detected due to timing between masters.
; 1.05 Added IFDEFs for SX28/52 and I2C/UART demo boards
; 1.06a Rewritten according to vp_guide_1_02.src, compabillity to SX48/52 and
; ISR cycle count. By Olav Gundersen
; 1.06b Added comments in program description, subroutines extended page moved to
; new page (PAGE4_ORG). By Olav Gundersen
;*****************************************************************************************
;*****************************************************************************************
; Target SX
; Uncomment one of the following lines to choose the SX18AC, SX20AC, SX28AC, SX48BD,
; or SX52BD.
;*****************************************************************************************
;SX18_20
SX28
;SX48_52
;*****************************************************************************************
; Assembler Used
; Uncomment the following line if using the Parallax SX-Key assembler. SASM assembler
; enabled by default.
;*****************************************************************************************
;SX_Key ; Uncomment this line to assemble this source code using the
; Parallax Assembler
;*********************************************************************************
; Assembler directives:
; high speed external osc, turbo mode, 8-level stack, and extended option reg.
;
; SX18/20/28 - 4 pages of program memory and 8 banks of RAM enabled by default.
; SX48/52 - 8 pages of program memory and 16 banks of RAM enabled by default.
;
;*********************************************************************************
IFDEF SX_Key ; SX-Key Directives
watch i2cmmRecvString,16,fstr ; Watch for simplify the debugging
watch i2cmmAddress,8,uhex ;
IFDEF SX18_20 ;SX18AC or SX20AC device directives for SX-Key
device SX18L,oschs2,turbo,stackx_optionx
ENDIF
IFDEF SX28 ;SX28AC device directives for SX-Key
device SX28L,oschs2,turbo,stackx_optionx
ENDIF
IFDEF SX48_52 ;SX48/52/BD device directives for SX-Key
device oschs2
ENDIF
freq 50_000_000
ELSE ;SASM Directives
IFDEF SX18_20 ;SX18AC or SX20AC device directives for SASM
device SX18,oschs2,turbo,stackx,optionx
ENDIF
IFDEF SX28 ;SX28AC device directives for SASM
device SX28,oschs2,turbo,stackx,optionx
ENDIF
IFDEF SX48_52 ;SX48BD or SX52BD device directives for SASM
device SX52,oschs2
ENDIF
ENDIF
multiMaster ; Enable the arbitration algorithm
id 'I2CMM' ; code identification
reset resetEntry ; set reset vector
;*****************************************************************************************
; Macros
;*****************************************************************************************
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
;
; To support compatibility between source code written for the SX28 and the SX52,
; use macros.
;
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
;*********************************************************************************
; Macro: _bank
; Sets the bank appropriately for all revisions of SX.
;
; This is required since the bank instruction has only a 3-bit operand, it cannot
; be used to access all 16 banks of the SX48/52. For this reason FSR.7 needs to be
; set appropriately, depending on the bank address being accessed. Use of this macro
; switches banks correctly, regardless of the part being compiled for.
;
; Instead of using the bank instruction to switch between banks, use _bank instead.
;
;*********************************************************************************
_bank macro 1 ;1,2
bank \1
IFDEF SX48_52
IF \1 & %10000000 ;SX48BD and SX52BD (production release) bank instruction
setb fsr.7 ;modifies FSR bits 4,5 and 6. FSR.7 needs to be set by software.
ELSE
clrb fsr.7
ENDIF
ENDIF
endm
;*****************************************************************************************
; Macros for SX28/52 Compatibility
;*****************************************************************************************
;*********************************************************************************
; Macro: _mode
; Sets the MODE register appropriately for all revisions of SX.
;
; This is required since the MODE (or MOV M,#) instruction has only a 4-bit operand.
; The SX18/20/28AC use only 4 bits of the MODE register, however the SX48/52BD have
; the added ability of reading or writing some of the MODE registers, and therefore use
; 5-bits of the MODE register. The MOV M,W instruction modifies all 8-bits of the
; MODE register, so this instruction must be used on the SX48/52BD to make sure the MODE
; register is written with the correct value. This macro fixes this.
;
; So, instead of using the MODE or MOV M,# instructions to load the M register, use
; _mode instead.
;
;*********************************************************************************
_mode macro 1
IFDEF SX48_52
expand
mov w,#\1 ;loads the M register correctly for the SX48BD and SX52BD
mov m,w
noexpand
ELSE
expand
mov m,#\1 ;loads the M register correctly for the SX18AC, SX20AC
noexpand ;and SX28AC
ENDIF
endm
;*****************************************************************************************
; INCP/DECP macros for incrementing/decrementing pointers to RAM
; used to compensate for incompatibilities between SX28 and SX52
;*****************************************************************************************
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
;
; To support compatibility between source code written for the SX28 and the SX52,
; use macros. This macro compensates for the fact that RAM banks are contiguous in
; the SX52, but separated by 0x20 in the SX18/28.
;
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
INCP macro 1
inc \1
IFNDEF SX48_52
setb \1.4 ; If SX18 or SX28, keep bit 4 of the pointer = 1
ENDIF ; to jump from $1f to $30, etc.
endm
DECP macro 1
IFDEF SX48_52
dec \1
ELSE
clrb \1.4 ; If SX18 or SX28, forces rollover to next bank
dec \1 ; if it rolls over. (Skips banks with bit 4 = 0)
setb \1.4 ; Eg: $30 --> $20 --> $1f --> $1f
ENDIF ; AND: $31 --> $21 --> $20 --> $30
endm
;*****************************************************************************************
; Error generating macros
; Used to generate an error message if the label is unintentionally moved into the
; second half of a page. Use for lookup tables.
;*****************************************************************************************
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
;
; Surround lookup tables with the tableStart and tableEnd macros. An error will
; be generated on assembly if the table crosses a page boundary.
;
; Example:
; lookupTable1
; add pc,w
; tableStart
; retw 0
; retw 20
; retw -20
; retw -40
; tableEnd
;
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
tableStart macro 0 ; Generates an error message if code that MUST be in
; the first half of a page is moved into the second half.
if $ & $100
ERROR 'Must be located in the first half of a page.'
endif
endm
tableEnd macro 0 ; Generates an error message if code that MUST be in
; the first half of a page is moved into the second half.
if $ & $100
ERROR 'Must be located in the first half of a page.'
endif
endm
;*****************************************************************************************
; Data Memory address definitions
; These definitions ensure the proper address is used for banks 0 - 7 for 2K SX devices
; (SX18/20/28) and 4K SX devices (SX48/52).
;*****************************************************************************************
IFDEF SX48_52
global_org = $0A
bank0_org = $00
bank1_org = $10
bank2_org = $20
bank3_org = $30
bank4_org = $40
bank5_org = $50
bank6_org = $60
bank7_org = $70
ELSE
global_org = $08
bank0_org = $10
bank1_org = $30
bank2_org = $50
bank3_org = $70
bank4_org = $90
bank5_org = $B0
bank6_org = $D0
bank7_org = $F0
ENDIF
;*****************************************************************************************
; Global Register definitions
; NOTE: Global data memory starts at $0A on SX48/52 and $08 on SX18/20/28.
;*****************************************************************************************
org global_org
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
;
; Use only these defined label types for global registers. If an extra temporary
; register is required, adhere to these label types. For instance, if two temporary
; registers are required for the Interrupt Service Routine, use the label isrTemp1
; for it.
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
flags0 equ global_org + 0 ; stores bit-wise operators like flags
; and function-enabling bits (semaphores)
;VP: RS232 Receive
rs232RxFlag equ flags0.0 ;indicates the reception of a bit from the UART
flags1 equ global_org + 1 ; stores bit-wise operators like flags
; and function-enabling bits (semaphores)
localTemp0 equ global_org + 2 ; temporary storage register
; Used by first level of nesting
; Never guaranteed to maintain data
localTemp1 equ global_org + 3 ; temporary storage register
; Used by second level of nesting
; or when a routine needs more than one
; temporary global register.
localTemp2 equ global_org + 4 ; temporary storage register
; Used by third level of nesting or by
; main loop routines that need a loop
; counter, etc.
isrTemp0 equ global_org + 5 ; Interrupt Service Routine's temp register.
; Don't use this register in the mainline.
i2cRecvChar equ $0F ; received character from EEPROM
;*****************************************************************************************
; RAM Bank Register definitions
;*****************************************************************************************
;*********************************************************************************
; Bank 0
;*********************************************************************************
org bank0_org
bank0 = $
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
; - Avoid using bank0 in programs written for SX48/52.
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
;*********************************************************************************
; Bank 1
;*********************************************************************************
org bank1_org
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
;
; Tip 1:
; Indicate which Virtual Peripherals a portion of source code or declaration belongs
; to with a
; ";VP: VirtualPeripheralName"
; comment.
;
; Tip 2:
; All RAM location declaration names should be
; - left justified
; - less than 2 tabs in length
; - written in hungarian notation
; - prefixed by a truncated version of the Virtual Peripheral's name
;
; Examples:
;
; ;VP: RS232 Transmit
;
; rs232TxBank = $ ;RS232 Transmit bank
;
; rs232TxHigh ds 1 ;hi byte to transmit
; rs232TxLow ds 1 ;low byte to transmit
; rs232TxCount ds 1 ;number of bits sent
; rs232TxDivide ds 1 ;xmit timing (/16) counter
; rs232TxString ds 1 ;the address of the string to be sent
; rs232TxByte ds 1 ;semi-temporary serial register
;
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
;VP: ISR Multithreader
isrMultiplex ds 1 ; The isrMultiplex register is used to switch to a new
; execution thread on each pass of the ISR.
;VP_end
;VP_begin I2C Multi-Master
i2cmmBank = $ ; I2CM bank
i2cmmState ds 1 ; This indicates the state that the I2CM master is currently in.
i2cmmSubState ds 1 ; This indicates the substate that the I2C master is currently in.
i2cmmPortBuf ds 1 ; This buffer holds the current state of the I2C port direction reg's
i2cmmBitCount ds 1 ; Indicates the number of bits left to process in read/write
i2cmmByte ds 1 ; The byte currently being written/read by the I2C master
i2cmmFlags ds 1
i2cmmNack equ i2cmmFlags.0 ; This bit is set if the I2C master has received a NACK from the slave
i2cmmRxFlag equ i2cmmFlags.1 ; Indicates that the number of bytes requested have been received
i2cmmLostArb equ i2cmmFlags.2 ; indicates that this master has lost arbitration
i2cmmDoingWrite equ i2cmmFlags.4 ; Used to remember whether doing a read or write when recovering from loss of arbitration
i2cmmInControl equ i2cmmFlags.5 ; Indicates that this master thinks it is in control of the I2C bus
i2cmmIndex ds 1 ; The index into the I2CM buffer, used for writing
i2cmmNumBytes ds 1 ; The index into the I2CM buffer, used for reading
i2cmmStrtCtr ds 1 ; Counts the number of SCL high cycles before sending a start bit onto the i2c-bus
i2cmmBuffer = $ ; The buffer uses the last 7 registers of this bank (pre-increments, so put I2CM buffer here.)
i2cmmAddress ds 1 ; The address to read/write to.
i2cmmDataBuf ds 6 ; Data buffer
; These data registers could easily be placed into another bank if more data memory is required
;VP_end ; End cut/paste for I2C MultiMaster
;*********************************************************************************
; Bank 2
;*********************************************************************************
org bank2_org
bank2 = $
;VP_begin I2C Multi-Master
i2cmmTimer = $
i2cmmTimerLow ds 1
i2cmmTimerHigh ds 1
VARS = $
i2cmmWritePtr ds 1 ; points to where data can be written
i2cmmReadAdr ds 1 ; used to point to address of slave to read
;VP_end ; End cut/paste for I2C MultiMaster
;*********************************************************************************
; Bank 3
;*********************************************************************************
org bank3_org
bank3 = $
;*********************************************************************************
; Bank 4
;*********************************************************************************
org bank4_org
bank4 = $
;*********************************************************************************
; Bank 5
;*********************************************************************************
org bank5_org
bank5 = $
;*********************************************************************************
; Bank 6
;*********************************************************************************
org bank6_org
bank6 = $
;*********************************************************************************
; Bank 7
;*********************************************************************************
org bank7_org
bank7 = $
;VP_begin I2C Multi-Master
i2cmmRecvString = $ ; where a string can be stored
;VP_end ; End cut/paste for I2C MultiMaster
IFDEF SX48_52
;*********************************************************************************
; Bank 8
;*********************************************************************************
org $80 ;bank 8 address on SX52
bank8 = $
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
; - This extra memory is not available in the SX18/28, so don't use it for Virtual
; Peripherals written for both platforms.
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
;*********************************************************************************
; Bank 9
;*********************************************************************************
org $90 ;bank 9 address on SX52
bank9 = $
;*********************************************************************************
; Bank A
;*********************************************************************************
org $A0 ;bank A address on SX52
bankA = $
;*********************************************************************************
; Bank B
;*********************************************************************************
org $B0 ;bank B address on SX52
bankB = $
;*********************************************************************************
; Bank C
;*********************************************************************************
org $C0 ;bank C address on SX52
bankC = $
;*********************************************************************************
; Bank D
;*********************************************************************************
org $D0 ;bank D address on SX52
bankD = $
;*********************************************************************************
; Bank E
;*********************************************************************************
org $E0 ;bank E address on SX52
bankE = $
;*********************************************************************************
; Bank F
;*********************************************************************************
org $F0 ;bank F address on SX52
bankF = $
ENDIF
;*********************************************************************************
; Pin Definitions:
;*********************************************************************************
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
; - Store all initialization constants for the I/O in the same area, so
; pins can be easily moved around.
; - Pin definitions should follow the same format guidelines as RAM definitions
; - Left justified
; - Hungarian Notation
; - Less that 2 tabs in length
; - Indicate the Virtual Peripheral the pin is used for
; - Only use symbolic names to access a pin/port in the source code.
; - Example:
; ; VP: RS232 Transmit
; rs232TxPin equ ra.3
;
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
RA_latch equ %11111111 ;SX18/20/28/48/52 port A latch init
RA_DDIR equ %11111111 ;SX18/20/28/48/52 port A DDIR value
RA_LVL equ %11111111 ;SX18/20/28/48/52 port A LVL value, set to CMOS
RA_PLP equ %00000000 ;SX18/20/28/48/52 port A PLP value, set to pull-up
;VP_begin I2C Multi-Master
i2cmmPort equ ra
scl equ 1
sda equ 0
i2cmmSclPin equ i2cmmPort.scl ; I2C clock
i2cmmSdaPin equ i2cmmPort.sda ; I2C data I/O
;VP_end ; End cut/paste for I2C MultiMaster
RB_latch equ %11111111 ;SX18/20/28/48/52 port B latch init
RB_DDIR equ %11111111 ;SX18/20/28/48/52 port B DDIR value
RB_ST equ %11111111 ;SX18/20/28/48/52 port B ST value
RB_LVL equ %00000000 ;SX18/20/28/48/52 port B LVL value
RB_PLP equ %00000000 ;SX18/20/28/48/52 port B PLP value
RC_latch equ %11111111 ;SX18/20/28/48/52 port C latch init
RC_DDIR equ %11111000 ;SX18/20/28/48/52 port C DDIR value, set to out on RC.0-2
RC_ST equ %11111111 ;SX18/20/28/48/52 port C ST value
RC_LVL equ %11111111 ;SX18/20/28/48/52 port C LVL value
RC_PLP equ %00000000 ;SX18/20/28/48/52 port C PLP value
;VP_begin I2C Multi-Master
i2cmmGreenLed equ rc.2
i2cmmRedLed2 equ rc.1
i2cmmRedLed1 equ rc.0
;VP_end ; End cut/paste for I2C MultiMaster
IFDEF SX48_52 ;SX48BD/52BD Port initialization values
RD_latch equ %00000000 ;SX48/52 port D latch init
RD_DDIR equ %11111111 ;SX48/52 port D DDIR value
RD_ST equ %11111111 ;SX48/52 port D ST value
RD_LVL equ %00000000 ;SX48/52 port D LVL value
RD_PLP equ %00000000 ;SX48/52 port D PLP value
RE_latch equ %00000000 ;SX48/52 port E latch init
RE_DDIR equ %11111111 ;SX48/52 port E DDIR value
RE_ST equ %11111111 ;SX48/52 port E ST value
RE_LVL equ %00000000 ;SX48/52 port E LVL value
RE_PLP equ %00000000 ;SX48/52 port E PLP value
ENDIF
;*****************************************************************************************
; Program constants
;*****************************************************************************************
;-------------------------------------------------------------------------------------
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
; To calculate the interrupt period in cycles:
; - First, choose the desired interrupt frequency
; - Should be a multiple of each Virtual Peripherals sampling frequency.
; - Example: 19200kHz UART sampling rate * 16 = 307.200kHz
; - Next, choose the desired oscillator frequency.
; - 50MHz, for example.
; - Perform the calculation intPeriod = (osc. frequency / interrupt frequency)
; = (50MHz / 307.2kHz)
; = 162.7604
; - Round intPeriod to the nearest integer:
; = 163
; - Now calculate your actual interrupt rate:
; = osc. frequency / intPeriod
; = 50MHz / 163
; = 306.748kHz
; - This interrupt frequency will be the timebase for all of the Virtual
; Peripherals
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
intPeriod = 86 ; Gives an interrupt period at 50MHz of (86 * (1/50000000)s) = 1.76us
; Which gives an interrupt frequency of (1/1.76us)Hz = 581.395kHz
; This is the double of the I2C bus frequency.
; intPeriod = clk_speed/(2x3 x bus_speed)
; e.g this intPeriod gives us a bus of:
; busSpeed= 50Mhz/(2 x 3 x intPeriod)= 96.9kHz
;VP_begin I2C Multi-Master
i2cmmSlaveAddr = $a0
;VP_end ; End cut/paste for I2C MultiMaster
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
; - Include all calculations for Virtual Peripheral constants for any sample
; rate.
; - Relate all Virtual Peripheral constants to the sample rate of the Virtual
; Peripheral.
; - Example:
; ; VP: 5ms Timer
; TIMER_DIV_CONST equ 192 ; This constant = timer sample rate/200Hz = 192
;
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
;-------------------------------------------------------------------------------------
IFDEF SX48_52
;*********************************************************************************
; SX48BD/52BD Mode addresses
; *On SX48BD/52BD, most registers addressed via mode are read and write, with the
; exception of CMP and WKPND which do an exchange with W.
;*********************************************************************************
; Timer (read) addresses
TCPL_R equ $00 ;Read Timer Capture register low byte
TCPH_R equ $01 ;Read Timer Capture register high byte
TR2CML_R equ $02 ;Read Timer R2 low byte
TR2CMH_R equ $03 ;Read Timer R2 high byte
TR1CML_R equ $04 ;Read Timer R1 low byte
TR1CMH_R equ $05 ;Read Timer R1 high byte
TCNTB_R equ $06 ;Read Timer control register B
TCNTA_R equ $07 ;Read Timer control register A
; Exchange addresses
CMP equ $08 ;Exchange Comparator enable/status register with W
WKPND equ $09 ;Exchange MIWU/RB Interrupts pending with W
; Port setup (read) addresses
WKED_R equ $0A ;Read MIWU/RB Interrupt edge setup, 0 = falling, 1 = rising
WKEN_R equ $0B ;Read MIWU/RB Interrupt edge setup, 0 = enabled, 1 = disabled
ST_R equ $0C ;Read Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
LVL_R equ $0D ;Read Port Level setup, 0 = CMOS, 1 = TTL
PLP_R equ $0E ;Read Port Weak Pullup setup, 0 = enabled, 1 = disabled
DDIR_R equ $0F ;Read Port Direction
; Timer (write) addresses
TR2CML_W equ $12 ;Write Timer R2 low byte
TR2CMH_W equ $13 ;Write Timer R2 high byte
TR1CML_W equ $14 ;Write Timer R1 low byte
TR1CMH_W equ $15 ;Write Timer R1 high byte
TCNTB_W equ $16 ;Write Timer control register B
TCNTA_W equ $17 ;Write Timer control register A
; Port setup (write) addresses
WKED_W equ $1A ;Write MIWU/RB Interrupt edge setup, 0 = falling, 1 = rising
WKEN_W equ $1B ;Write MIWU/RB Interrupt edge setup, 0 = enabled, 1 = disabled
ST_W equ $1C ;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
LVL_W equ $1D ;Write Port Level setup, 0 = CMOS, 1 = TTL
PLP_W equ $1E ;Write Port Weak Pullup setup, 0 = enabled, 1 = disabled
DDIR_W equ $1F ;Write Port Direction
ELSE
;*********************************************************************************
; SX18AC/20AC/28AC Mode addresses
; *On SX18/20/28, all registers addressed via mode are write only, with the exception of
; CMP and WKPND which do an exchange with W.
;*********************************************************************************
; Exchange addresses
CMP equ $08 ;Exchange Comparator enable/status register with W
WKPND equ $09 ;Exchange MIWU/RB Interrupts pending with W
; Port setup (read) addresses
WKED_W equ $0A ;Write MIWU/RB Interrupt edge setup, 0 = falling, 1 = rising
WKEN_W equ $0B ;Write MIWU/RB Interrupt edge setup, 0 = enabled, 1 = disabled
ST_W equ $0C ;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
LVL_W equ $0D ;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
PLP_W equ $0E ;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
DDIR_W equ $0F ;Write Port Direction
ENDIF
;VP_begin I2C Multi-Master
i2cmmStrtDelay = 4 ; This start delay is critical in the operation
; of the multi-master system. The value of i2cmmStrtDelay
; specifies the number of ISR's that the scl line must
; be held high for before a start bit will be sent.
; If all masters on the I2C bus are running at the same clock speed, simply leave the value set
; at 4. If for example one of the masters is running twice as fast as another then this value may
; need to be changed. A good rule of thumb is the slowest master must have a delay of at least 4 and the
; faster masters use multiples of that relative to their clock speeds. The principle of this is
; simply to keep the length of the start bit the same no matter which master is using the bus. This
; makes it easy to detect and know when it is okay to use the bus. The other reason for changing this
; value is to change the relative amount of time that each master will be allocated.
; eg. run SX 1 with intPeriod = 166 (100kHz) and i2cmmStrtDelay = 4
; SX 2 with intPeriod = 111 (150kHz) and i2cmmStrtDelay = 6
; Running at 100kHz with 50Mhz clock, a i2cmmStrtDelay of 3 gives a start+stop pulse of approx. 24us
; The higher the delay the less timing critical arbitration will be. For instance if the i2cmmStrtDelay is
; 3 this will work fine only as long as other masters are running at the same frequency. But if you
; increase the value to 4 you will find that operation will still continue fine even with a difference
; of 50kHz, as in the example settings above.
; If you are not running this master in multi-master mode it is possible to decrease the start_delay
; to 1, this improves data throughput by reducing the width of the start+stop pulse to 17us.
IFNDEF multiMaster
i2cmmStrtDelay = 1
ENDIF
;VP_end ; End cut/paste for I2C MultiMaster
;*****************************************************************************************
; Program memory ORG defines
;*****************************************************************************************
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
; - Place a table at the top of the source with the starting addresses of all of
; the components of the program.
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
INTERRUPT_ORG equ $0 ; Interrupt must always start at location zero
RESET_ENTRY_ORG equ $1FB ; The program will jump here on reset.
SUBROUTINES_ORG equ $200 ; The subroutines are in this location
STRINGS_ORG equ $300 ; The strings are in location $300
PAGE3_ORG equ $400 ; Page 3 is empty
PAGE4_ORG equ $500 ; Additional subroutines for I2CMM
MAIN_PROGRAM_ORG equ $600 ; The main program is in the last page of program memory.
;****************************** Beginning of program space *******************************
;*****************************************************************************************
;*****************************************************************************************
;*****************************************************************************************
org INTERRUPT_ORG ; First location in program memory.
;*****************************************************************************************
;------------------------------------------------------------------------------
; Interrupt Service Routine
;------------------------------------------------------------------------------
; Note: The interrupt code must always originate at address $0.
;
; Interrupt Frequency = (Cycle Frequency / -(retiw value)) For example:
; With a retiw value of -163 and an oscillator frequency of 50MHz, this
; code runs every 3.26us.
;------------------------------------------------------------------------------
ISR ;3 The interrupt service routine...
;------------------------------------------------------------------------------
;VP: VP Multitasker
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
; - Multi-thread the Interrupt Service Routine
; - Produces a FAR smaller worst-case cycle time count, and enables a larger number
; of VP's to run simultaneously. Also produces "empty" slots that future VP's
; can be copied and pasted into easily.
; - Determine how often your tasks need to run. (9600bps UART can run well at a
; sampling rate of only 38400Hz, so don't run it faster than this.)
; - Strategically place each "module" into the threads of the ISR. If a module
; must be run more often, just call it's module at double the rate or quadruple
; the rate, etc.…
; - Split complicated Virtual Peripherals into several modules, keeping the
; high-speed portions of the Virtual Peripherals as small and quick as possible,
; and run the more complicated, slower processing part of the Virtual Peripheral
; at a lower rate.
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
;------------------------------------------------------------------------------
; Virtual Peripheral Multitasker: up to 24 individual threads, each running at
; the interrupt rate/24. Change the number of
; table entries for each thread to change the
; sample rate of that thread.
;
; Input variable(s): isrMultiplex: variable used to choose threads
; Output variable(s): None, executes the next thread
; Variable(s) affected: isrMultiplex
; Flag(s) affected: None
; Program Cycles: 9 cycles (turbo mode SX28)
;------------------------------------------------------------------------------
_bank isrMultiplex ;1 (or 2 in SX52)
inc isrMultiplex ;1 ; toggle interrupt rates
mov w,isrMultiplex ;1
; The code between the tableBegin and tableEnd statements MUST be
; completely within the first half of a page. The routines
; it is jumping to must be in the same page as this table.
tableStart ; Start all tables with this macro.
add pc,w ;3
jmp isrThread1 ;3 = 9/10 + 52/76 = 61/86 cycles
jmp isrThread2 ;
jmp isrThread1 ;
jmp isrThread3 ;
jmp isrThread1 ;
jmp isrThread4 ;
jmp isrThread1 ;
jmp isrThread5 ;
jmp isrThread1 ;
jmp isrThread2 ;
jmp isrThread1 ;
jmp isrThread6 ;
jmp isrThread1 ;
jmp isrThread7 ;
jmp isrThread1 ;
jmp isrThread3 ;
jmp isrThread1 ;
jmp isrThread2 ;
jmp isrThread1 ;
jmp isrThread8 ;
jmp isrThread1 ;
jmp isrThread9 ;
jmp isrThread1 ;
jmp isrThread16 ;
tableEnd ; End all tables with this macro.
;------------------------------------------------------------------------------
;VP: VP Multitasker
; ISR TASKS
;------------------------------------------------------------------------------
isrThread1 ; Serviced at ISR rate / 2
;------------------------------------------------------------------------------
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
; The sample rate of this section of code is the isr rate / 2, because it is jumped
; to in every 2nd entry in the VP Multitaskers table. To increase the
; sample rate, put more calls to this thread in the Multitasker's jump table.
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
;VP_begin I2C Multi-Master
;*********************************************************************************
; Keep running 8bit timer...
; Uncomment the two lines below if a 16 bit timer is needed (be aware that this
; adds two cycles to this ISR thread).
;*********************************************************************************
_bank i2cmmTimer ;1 (or 2 in SX48/52)
inc i2cmmTimerLow ;1
; snz ;1
; inc i2cmmTimerHigh ;1
;= 2/3 + 9 = 11/12
;*********************************************************************************
; I2C Master Virtual Peripheral
;*********************************************************************************
_bank i2cmmBank ;1 (or 2 in SX52)
mov w,#i2cmmBuffer ;1 ; Switch to I2CM bank and load FSR for
mov fsr,w ;1 ; buffer look-up, if needed.
call @i2cmmISR ;3 + i2cmmISR = 17/18 + 12/26 =
; = 29/44
;*********************************************************************************
; Update I2C port with buffered port data
;*********************************************************************************
mov w,m ;1 ; Save the m register.
mov isrTemp0,w ;1
_mode DDIR_W ;1 (2 for 48/52
mov w,i2cmmPort ;1
and w,#%11110000 ;1 ; Clear the data latches for SCL and SDA
mov i2cmmPort,w ;1
_bank i2cmmBank ;1 (or 2 in SX52)
mov w,i2cmmPortBuf ;1
mov !i2cmmPort,w ;1 ; Update the I2C port with the buffered port data
mov w,isrTemp0 ;1 ; Restore the m register.
mov m,w ;1
;= 11/13 + 29/44 = 40/57
;*********************************************************************************
; i2cmmArbitration
; This code checks to see that the data written by I2CM is the same
; as the data present on the bus. If not, this master has lost arbitration.
;*********************************************************************************
IFDEF multiMaster
i2cmmArb
_bank i2cmmBank ;1 (or 2 in SX52)
; --- Check if arbitration required ---
snb i2cmmLostArb ;1 ; No need to check if lost arb. already lost
jmp i2cmmArbDone ;3
sb i2cmmInControl ;1 ; Only check arbitration when master is in control
jmp i2cmmArbDone ;3
; --- Check if data on bus matches data written by master ---
snb i2cmmSdaPin ;1 ; No master can have lost arb. when sda is high
jmp i2cmmArbDone ;3
sb i2cmmPortBuf.sda ;1 ; check if buffer wants data high, if it does master loses arb.
jmp i2cmmArbDone ;3
; --- Arbitration has been lost. The master must now wait a 'random' time before trying again ---
:i2cmmArbLost setb i2cmmLostArb ;1 ; signal a loss of arbitration (just lost)
clr i2cmmState ;1 ; Put state machine into IDLE state
clr i2cmmSubState ;1
i2cmmArbDone ; = 5/12 + 40/57 = 45/69
ENDIF
;VP_end ; End cut/paste for I2C MultiMaster
jmp isrOut ;7 cycles until mainline program resumes execution
; = 7 + 45/69 = 52/76
;------------------------------------------------------------------------------
isrThread2 ; Serviced at ISR rate / 8
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread3 ; Serviced at ISR rate / 12
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread4 ; Serviced at ISR rate / 24
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread5 ; Serviced at ISR rate / 24
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread6 ; Serviced at ISR rate / 24
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread7 ; Serviced at ISR rate / 24
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread8 ; Serviced at ISR rate / 24
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread9 ; Serviced at ISR rate / 24
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread10 ; Never serviced
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread11 ; Never serviced
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread12 ; Never serviced
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread13 ; Never serviced
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread14 ; Never serviced
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread15 ; Never serviced
;------------------------------------------------------------------------------
jmp isrOut ;7 cycles until mainline program resumes execution
;------------------------------------------------------------------------------
isrThread16 ; Serviced at ISR rate / 24
; ; This thread must reload the isrMultiplex register
; since it is the last one to run in a rotation.
;------------------------------------------------------------------------------
_bank isrMultiplex
mov w,#255 ; Reload isrMultiplex so isrThread1 will be run
mov isrMultiplex,w ; on next interrupt.
jmp isrOut
;------------------------------------------------------------------------------
;------------------------------------------------------------------------------
isrOut
;------------------------------------------------------------------------------
mov w,#-intPeriod ;1 ; return and add -intPeriod to the RTCC
retiw ;3 ; using the retiw instruction.
;------------------------------------------------------------------------------
;*****************************************************************************************
org RESET_ENTRY_ORG
;*****************************************************************************************
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
; The main program operation should be easy to find, so place it at the end of the
; program code. This means that if the first page is used for anything other than
; main program source code, a reset_entry must be placed in the first page, along
; with a 'page' instruction and a 'jump' instruction to the beginning of the
; main program.
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
;------------------------------------------------------------------------------
resetEntry ; Program starts here on power-up
page _resetEntry
jmp _resetEntry
;------------------------------------------------------------------------------
;*****************************************************************************************
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
; ORG statements should use predefined labels rather than literal values.
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
org SUBROUTINES_ORG
;*****************************************************************************************
; Subroutines
;*****************************************************************************************
;VP_begin I2C Multi-Master
;*****************************************************************************************
; I2C Master Interrupt Service Routines
;*****************************************************************************************
; I2C Virtual Peripheral...
;*********************************************************************************
; Function: i2cmmISR
; I2C Master Interrupt-Driven State Machine
; -------------------------------------------
; This is the I2C Master Interrupt Service Routine. It is an interrupt-
; driven state machine which allows all of the actions of the I2C Master
; controller to be carried out, virtual peripheral style, with virtually
; no interaction from the mainline program.
; i2cmmIdle
; This is the state that the I2C Master is usually in when it is not in use.
; It just ensures that the I2C_port_buf SCL and SDA are both set high
; i2cmmStart
; When any mainline program wants to use the I2C master it puts the master into
; start mode. This mode creates a start condition on the I2C bus. A start
; condition is created when SDA goes from high to low while SCL stays high.
; i2cmmStartWrite
; This state performs some pre-processing which allows the i2cmmWrite state to
; do its work. It sets up the bit count, gets the next piece of data from the
; buffer and prepares to send it.
; i2cmmWrite
; This state writes the data in i2cmmByte to the I2C bus
; i2cmmGetAck
; This state gets an ACK from the slave device. If no ACK is received, the I2C
; Master state machine puts a stop condition on the bus and the i2cmmFlags
; register is loaded to indicate that a NACK has occurred.
; i2cmmWriteRepeat
; This state determines, after one byte of data is sent, whether or not
; there is another byte to be sent. If so, this state goes back to i2cmmStartWrite
; and sends the next byte.
; i2cmmStop
; This state puts a stop condition on the I2C bus and resets the state machine back
; to its idle state. A stop condition is when SDA goes from low to high while SCL
; is high.
; i2cmmStartRead
; This state simply loads the contents of the i2cmmAddress register into the i2cmmByte
; register and sets up the i2cmmWrite state to output the address of the slave to read.
; i2cmmReadData
; This state prepares the I2CM read routine so it can read from the slave device. It
; initializes the bit count, etc.
; i2cmmRead
; This state read 8 bits of data from the slave device.
; i2cmmStoreByte
; This state stores the byte just read into the buffer.
; i2cmmSendAck
; This state sends an ack if there is data left to write, and a NACK if there is
; no data left to write.
;*********************************************************************************
i2cmmISR
mov w,i2cmmState ;1
; The code between the tableStart and tableEnd statements
; MUST be completely within the first half of a page. The routines
tableStart ; it is jumping to must be in the same page as this table.
add PC,w ;3 ;Add the state to the program counter
;and go to the state in the jump table.
;*************************************************************************
; States for I2C Master while idle
;*************************************************************************
i2cmmIdleLoc = $
jmp i2cmmIdle ;3 ;If I2C_state = 0, I2C is idle
;*************************************************************************
; States for I2C Master while writing
;*************************************************************************
i2cmmWriteLoc = $
jmp i2cmmStart ;3 ;Make SDA go low while SCL is high
jmp i2cmmStartWrite ;3 ;Load a byte from the buffer and prepare to send.
jmp i2cmmWrite ;3 ;Write it.
jmp i2cmmGetAck ;3 ;Get an ACK signal
jmp i2cmmWriteRepeat ;3 ;Check to see if we have finished sending
;(if buffer read index = buffer write index)
i2cmmStopLoc = $
jmp i2cmmStop ;3 ;If write_repeat determines we're finished,
;then send stop
;*************************************************************************
; States for I2C Master while reading
;*************************************************************************
i2cmmReadLoc = $ ;Load this state into state machine if we
;are starting to read
jmp i2cmmStart ;3 ;
jmp i2cmmStartRead ;3 ;Write address used for reading
jmp i2cmmWrite ;3 ;(writing address)
jmp i2cmmGetAck ;3 ;
i2cmmReadRptLoc = $
jmp i2cmmReadData ;3 ;
jmp i2cmmRead ;3 ;Keep doing this until done
jmp i2cmmStoreByte ;3 ;
jmp i2cmmSendAck ;3 ;
jmp i2cmmStop ;3 ;
tableEnd ; = 7 (from i2cmmISR to here)
;*********************************************************************************
; State: i2cmmIdle
; This is the state that the I2C Master is usually in when it is not in use.
; It just ensures that the I2C_port_buf SCL and SDA are both set high
;*********************************************************************************
i2cmmIdle setb i2cmmPortBuf.sda ;1
setb i2cmmPortBuf.scl ;1
retp ;3 = 5 + 7 = 12
;*********************************************************************************
; State: i2cmmStart
; When any mainline program wants to use the I2C master it puts the master into
; start mode. This mode creates a start condition on the I2C bus. A start
; condition is created when SDA goes from high to low while SCL stays high.
;*********************************************************************************
i2cmmStart mov w,i2cmmSubState ;1
; The code between the tableStart and tableEnd statements
; MUST be completely within the first half of a page. The routines
tableStart ; it is jumping to must be in the same page as this table.
add pc,w ;3
jmp :state1 ;3
jmp :state2 ;3
jmp :state3 ;3
jmp :state4 ;3
jmp :state5 ;3 = 7 + 7 = 14
tableEnd
:state1 setb i2cmmPortBuf.scl ;1
setb i2cmmInControl ;1
setb i2cmmPortBuf.sda ;1
inc i2cmmSubState ;1
mov w,#i2cmmStrtDelay ;1
mov i2cmmStrtCtr,w ;1
retp ;3 = 9 + 14 = 23
; --- WAITING FOR STOP/START OR IDLE SCL ---
:state2 sb i2cmmSclPin ;1
clr i2cmmSubState ;1
decsz i2cmmStrtCtr ;1
retp ;3 = 6 + 14 = 20
inc i2cmmSubState ;1
retp ;3 = 8 + 14 = 22
; --- FINISHED CLOCK SYNCRONIZATION PERIOD ---
:state3 clrb i2cmmPortBuf.sda ;1
inc i2cmmSubState ;1
retp ;3 = 5 + 14 = 19
:state4 clrb i2cmmPortBuf.scl ;1
inc i2cmmSubState ;1
retp ;3 = 5 + 14 = 19
:state5 setb i2cmmPortBuf.sda ;1
clr i2cmmSubState ;1
inc i2cmmState ;1
retp ;3 = 6 + 14 = 20
;*********************************************************************************
; State: i2cmmStartWrite
; This state performs some pre-processing which allows the i2cmmWrite state to
; do its work. It sets up the bit count, gets the next piece of data from the
; buffer and prepares to send it.
;*********************************************************************************
i2cmmStartWrite
inc i2cmmIndex ;1
mov w,i2cmmIndex ;1
add fsr,w ;1
mov w,indf ;1
mov i2cmmByte,w ;1
mov w,#8 ;1
mov i2cmmBitCount,w ;1
inc i2cmmState ;1
retp ;3 = 11 + 7 = 18
;*********************************************************************************
; State: i2cmmWrite
; This state writes the data in i2cmmByte to the I2C bus
;*********************************************************************************
i2cmmWrite mov w,i2cmmSubState ;1
; The code between the tableStart and tableEnd statements
; MUST be completely within the first half of a page. The routines
tableStart ; it is jumping to must be in the same page as this table.
add pc,w ;3
jmp :state1 ;3
jmp :state2 ;3
jmp :state3 ;3 = 7 + 7 = 14
tableEnd
:state1 setb i2cmmInControl ;1
setb i2cmmPortBuf.sda ;1
rl i2cmmByte ;1
sb c ;1
clrb i2cmmPortBuf.sda ;1
inc i2cmmSubState ;1
retp ;3 = 9 + 14 = 23
:state2 setb i2cmmPortBuf.scl ;1
inc i2cmmSubState ;1
retp ;3 = 5 + 14 = 19
:state3 clrb i2cmmPortBuf.scl ;1
dec i2cmmBitCount ;1
snb z ;1
jmp :done ;3
clr i2cmmSubState ;1
retp ;3 = 8 + 14 = 22
:done clr i2cmmSubState ;1
inc i2cmmState ;1
clrb i2cmmInControl ;1
retp ;3 = 12 + 14 = 26
;*********************************************************************************
; State: i2cmmGetAck
; This state gets an ACK from the slave device. If no ACK is received, the I2C
; Master state machine puts a stop condition on the bus and the i2cmmFlags
; register is loaded to indicate that a NACK has occurred.
;*********************************************************************************
i2cmmGetAck mov w,i2cmmSubState ;1
; The code between the tableStart and tableEnd statements
; MUST be completely within the first half of a page. The routines
tableStart ; it is jumping to must be in the same page as this table.
add pc,w ;3
jmp :state1 ;3
jmp :state2 ;3
jmp :state3 ;3
jmp :state4 ;3 = 7 + 7 = 14
tableEnd
:state1 setb i2cmmPortBuf.sda ;1
inc i2cmmSubState ;1
retp ;3 = 5 + 14 = 19
:state2 setb i2cmmPortBuf.scl ;1
inc i2cmmSubState ;1
retp ;3 = 5 + 14 = 19
:state3 sb i2cmmSdaPin ;1
inc i2cmmSubState ;1
sb i2cmmSdaPin ;1
retp ;3 = 6 + 14 = 20 ;if ack,
mov w,#(i2cmmStopLoc-i2cmmIdleLoc);1
mov i2cmmState,w ;1
clr i2cmmSubState ;1 ;send a stop and indicate that this didn't work.
setb i2cmmNack ;1 ;set i2cmmNack to show that this did not go through.
retp ;3 = 11 + 14 = 25
:state4 clrb i2cmmPortBuf.scl ;1
clr i2cmmSubState ;1
inc i2cmmState ;1 ;move on to next state
retp ;3 = 6 + 14 = 20
;*********************************************************************************
; State: i2cmmWriteRepeat
; This state determines, after one byte of data is sent, whether or not
; there is another byte to be sent. If so, this state goes back to
; i2cmmStartWrite and sends the next byte.
;*********************************************************************************
i2cmmWriteRepeat
mov w,i2cmmNumBytes ;1 ;test the read index to see if it is = to write index.
xor w,i2cmmIndex ;1 ;if it is, then we have finished writing the buffer via. I2C.
snb z ;1
jmp :i2cmmWriteDone ;3
dec i2cmmState ;1 ;back to GetAck
dec i2cmmState ;1 ;back to Write
dec i2cmmState ;1 ;back to StartWrite
retp ;3 = 10 + 7 = 17
:i2cmmWriteDone
inc i2cmmState ;1 ;move on to next state (stop)
retp ;3 = 10 + 7 = 17 ;and start the stop bit
;*********************************************************************************
; State: i2cmmStop
; This state puts a stop condition on the I2C bus and resets the state machine back
; to its idle state. A stop condition is when SDA goes from low to high while SCL
; is high.
;*********************************************************************************
i2cmmStop mov w,i2cmmSubState ;1
; The code between the tableStart and tableEnd statements
; MUST be completely within the first half of a page. The routines
tableStart ; it is jumping to must be in the same page as this table.
add pc,w ;3
jmp :state1 ;3
jmp :state2 ;3
jmp :state3 ;3 = 7 + 7 = 14
tableEnd
:state1 setb i2cmmInControl ;1
clrb i2cmmPortBuf.sda ;1
inc i2cmmSubState ;1
retp ;3 = 6 + 14 = 20
:state2 setb i2cmmPortBuf.scl ;1
inc i2cmmSubState ;1
retp ;3 = 5 + 14 = 19
:state3 setb i2cmmPortBuf.sda ;1
clr i2cmmSubState ;1
clr i2cmmState ;1 ;put the state machine in Idle
clr i2cmmNumBytes ;1
mov w,#$ff ;1
mov i2cmmIndex,w ;1
clrb i2cmmInControl ;1
retp ;3 = 10 + 14 = 24
;*****************************************************************************************
; End of I2C Master state machine
;*****************************************************************************************
;*****************************************************************************************
; Jump table
;*****************************************************************************************
i2cmmSendByte jmp i2cmmSendByte_ ;3
i2cmmSendBytes jmp i2cmmSendBytes_ ;3
i2cmmGetByte jmp i2cmmGetByte_ ;3
i2cmmGetBytes jmp i2cmmGetBytes_ ;3
i2cmmWaitNotBusy jmp i2cmmWaitNotBusy_ ;3
i2cmmInit jmp i2cmmInit_ ;3
;*****************************************************************************************
; I2C Master Subroutines
;*****************************************************************************************
;*********************************************************************************
; Function: i2cmmStartRead
; This state simply loads the contents of the i2cmmAddress register into the
; i2cmmByte register and sets up the i2cmmWrite state to output the address
; of the slave to read.
;*********************************************************************************
i2cmmStartRead
mov w,i2cmmAddress
mov i2cmmByte,w
inc i2cmmIndex
mov w,#8
mov i2cmmBitCount,w
inc i2cmmState
retp
;*********************************************************************************
; Function: i2cmmReadData
; This function prepares the I2CM read routine so it can read from the slave
; device. It initializes the bit count, etc.
;*********************************************************************************
i2cmmReadData
mov w,#8
mov i2cmmBitCount,w
inc i2cmmState
;*************************************************************************
; Read 8 bits of data from the slave device.
;*************************************************************************
i2cmmRead mov w,i2cmmSubState
; The code between the tableStart and tableEnd statements
; MUST be completely within the first half of a page. The routines
tableStart ; it is jumping to must be in the same page as this table.
add pc,w
jmp :state1
jmp :state2
jmp :state3
tableEnd
:state1 clrb i2cmmInControl
setb i2cmmPortBuf.scl
inc i2cmmSubState
retp
:state2 sb i2cmmSclPin
retp
stc
sb i2cmmSdaPin
clc
rl i2cmmByte
inc i2cmmSubState
retp
:state3 clrb i2cmmPortBuf.scl
clr i2cmmSubState
dec i2cmmBitCount
sb z
retp
inc i2cmmState
retp
;*********************************************************************************
; Function: i2cmmStoreByte
; This function stores the byte just read into the buffer.
;*********************************************************************************
i2cmmStoreByte
mov w,i2cmmByte
mov isrTemp0,w
inc i2cmmIndex
mov w,i2cmmIndex
add fsr,w
mov w,isrTemp0
mov indf,w
inc i2cmmState
setb i2cmmRxFlag
retp
;*********************************************************************************
; Function: i2cmmSendAck
; This function sends an ack if there is data left to write, and a NACK if
; there is no data left to write.
;*********************************************************************************
i2cmmSendAck
mov w,i2cmmSubState
; The code between the tableStart and tableEnd statements
; MUST be completely within the first half of a page. The routines
tableStart ; it is jumping to must be in the same page as this table.
add pc,w
jmp :state1
jmp :state2
jmp :state3
jmp :state4
tableEnd
:state1 setb i2cmmInControl
clrb i2cmmPortBuf.sda
mov w,i2cmmIndex
xor w,i2cmmNumBytes
snz
setb i2cmmPortBuf.sda
inc i2cmmSubState
retp
:state2 setb i2cmmPortBuf.scl ;Pulse the clock
inc i2cmmSubState
retp
:state3 sb i2cmmSclPin
retp
clrb i2cmmPortBuf.scl
inc i2cmmSubState
retp
:state4 setb i2cmmPortBuf.sda
clr i2cmmSubState
mov w,i2cmmIndex
xor w,i2cmmNumBytes
snz
jmp :done
mov w,#(i2cmmReadRptLoc - i2cmmIdleLoc) ;back to read
mov i2cmmState,w
retp
:done inc i2cmmState ;If this was the last byte to be read, send a stop
retp
;*****************************************************************************************
; I2C Master Subroutines: Mainline Access routines (call from the mainline)
;*****************************************************************************************
;*********************************************************************************
; Function: i2cmmSendByte
; This routine sets up the I2CM state machine to write the byte of data in
; the i2cmmDataBuf register. Before entering this routine, make sure that
; the I2CM state machine is in its idle state (use the i2cmmWaitNotBusy
; subroutine) and that the i2cmmAddress is loaded with the address of the
; slave that this byte is going to, and that i2cmmDataBuf is loaded with the
; data to send.
;*********************************************************************************
i2cmmSendByte_
mov w,#1 ;There is one byte of data in the buffer
mov i2cmmNumBytes,w
;*********************************************************************************
; Function: i2cmmSendBytes
; This routine sets up the I2CM state machine to write the bytes of data in
; the i2cmmDataBuf registers. Before entering this routine,
; make sure that the I2CM state machine is in its idle state (use the
; i2cmmWaitNotBusy subroutine) and that i2cmmAddress is loaded with the
; address of the slave that this byte is going to, that i2cmmDataBuf
; are loaded with the data to send, and that the i2cmmNumBytes register
; is loaded with the number of data bytes to send.
;*********************************************************************************
i2cmmSendBytes_
setb i2cmmDoingWrite
mov w,#%11111110
and i2cmmAddress,w
clrb i2cmmNack
mov w,#(i2cmmWriteLoc-i2cmmIdleLoc)
mov i2cmmState,w
retp
;*********************************************************************************
; Function: i2cmmWaitNotBusy
; This routine polls the i2cmmState register until it is not busy. It returns
; when the I2C master state machine becomes idle. It returns a (0) in the w
; register if the transfer appeared successful (ie. The slave returned an ACK
; when addressed), and a (1) in the w register if the slave did not return
; an ack when addressed/written.
;*********************************************************************************
i2cmmWaitNotBusy_
:wait_loop test i2cmmState
sb z ; wait until I2C is idle
jmp :wait_loop
mov w,#1 ; return (1) if we are idle because a NACK was
snb i2cmmNack ; received. Return (0) if we are idle because
retp ; this was successful
clr w
retp
;*********************************************************************************
; Function: i2cmmGetByte
; This routine gets one byte of data from the slave at address i2cmmAddress.
; before calling this routine, ensure that the I2C Master State Machine is
; in its idle state (use the i2cmmWaitNotBusy subroutine) and that the
; i2cmmAddress register is loaded with a valid address. The routine returns
; with the byte received in the w register and in the i2cmmDataBuf register.
;*********************************************************************************
i2cmmGetByte_
clrb i2cmmDoingWrite
:nack mov w,#%00000001
or i2cmmAddress,w
mov w,#1
mov i2cmmNumBytes,w
clrb i2cmmNack
mov w,#(i2cmmReadLoc-i2cmmIdleLoc)
mov i2cmmState,w
call i2cmmWaitNotBusy
and w,#$ff
sz
jmp :nack
clrb i2cmmRxFlag
mov w,i2cmmDataBuf
retp
;*********************************************************************************
; Remaining functions (i2cmmGetBytes and i2cmmInit) is moved to PAGE4_ORG
; because of insufficient space in this page...
;*********************************************************************************
;VP_end ; End cut/paste for I2C MultiMaster
;*****************************************************************************************
org STRINGS_ORG ; This label defines where strings are kept in program space.
;*****************************************************************************************
;------------------------------------------------------------------------------
; Put String Data Here
;------------------------------------------------------------------------------
; Example:
;_hello dw 13,10,'UART Demo',0
jmp $ ; This instruction will cause an assembler error if the source code before
; the org statement inadvertantly crosses a page boundary.
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
; - Routines that use location-dependant data, such as in example below, should
; use a LABEL rather than a literal value as their input. Example:
; instead of
; mov m,#3 ; move upper nybble of address of strings into m
; use
; mov m,#STRINGS_ORG>>8; move upper nybble of address of strings into m
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
;*****************************************************************************************
org PAGE3_ORG
;*****************************************************************************************
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
; To ensure that several Virtual Peripherals, when pasted together, do not cross
; a page boundary without the integrator's knowledge, put an ORG statement and one
; instruction at every page boundary. This will generate an error if a pasted
; subroutine moves another subroutine to a page boundary.
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
jmp $ ; This instruction will cause an assembler error if the source code before
; the org statement inadvertantly crosses a page boundary.
;*****************************************************************************************
org PAGE4_ORG
;*****************************************************************************************
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
; To ensure that several Virtual Peripherals, when pasted together, do not cross
; a page boundary without the integrator's knowledge, put an ORG statement and one
; instruction at every page boundary. This will generate an error if a pasted
; subroutine moves another subroutine to a page boundary.
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
;VP_begin I2C Multi-Master
;*********************************************************************************
; FUNCTIONS moved from SUBROUTINES because of insufficient space
;*********************************************************************************
;*********************************************************************************
; Function: i2cmmGetBytes
; This routine gets i2cmmNumBytes of data from the slave at address
; i2cmmAddress. Before calling this routine, ensure that the I2CM state
; machine is idle by using the i2cmmWaitNotBusy subroutine, that i2cmmAddress
; register contains the address of the slave to be read from, and that the
; i2cmmNumBytes register is loaded with the number of bytes of data to receive.
; The received bytes will be contained in registers i2cmmDataBuf.
;*********************************************************************************
i2cmmGetBytes_
clrb i2cmmDoingWrite
mov w,#%00000001
or i2cmmAddress,w
clrb i2cmmNack
clrb i2cmmRxFlag
mov w,#(i2cmmReadLoc-i2cmmIdleLoc)
mov i2cmmState,w
retp
;*********************************************************************************
; Function: i2cmmInit
; This subroutine should be called on startup. It initializes the registers
; which are critical to the operation of the I2CM state machine.
;*********************************************************************************
i2cmmInit_
mov w,#%10111111 ;Set RB in/out directions
mov i2cmmPortBuf,w
mov w,#$ff
mov i2cmmNumBytes,w
mov w,#$ff
mov i2cmmIndex,w
retp
;VP_end ; End cut/paste for I2C MultiMaster
;*****************************************************************************************
org MAIN_PROGRAM_ORG
;*****************************************************************************************
;------------------------------------------------------------------------------
; RESET VECTOR
;------------------------------------------------------------------------------
;------------------------------------------------------------------------------
; Program execution begins here on power-up or after a reset
;------------------------------------------------------------------------------
_resetEntry
;------------------------------------------------------------------------------
; Initialize all port configuration
;------------------------------------------------------------------------------
_mode ST_W ;point MODE to write ST register
mov w,#RB_ST ;Setup RB Schmitt Trigger, 0 = enabled, 1 = disabled
mov !rb,w
mov w,#RC_ST ;Setup RC Schmitt Trigger, 0 = enabled, 1 = disabled
mov !rc,w
IFDEF SX48_52
mov w,#RD_ST ;Setup RD Schmitt Trigger, 0 = enabled, 1 = disabled
mov !rd,w
mov w,#RE_ST ;Setup RE Schmitt Trigger, 0 = enabled, 1 = disabled
mov !re,w
ENDIF
_mode LVL_W ;point MODE to write LVL register
mov w,#RA_LVL ;Setup RA CMOS or TTL levels, 0 = TTL, 1 = CMOS
mov !ra,w
mov w,#RB_LVL ;Setup RB CMOS or TTL levels, 0 = TTL, 1 = CMOS
mov !rb,w
mov w,#RC_LVL ;Setup RC CMOS or TTL levels, 0 = TTL, 1 = CMOS
mov !rc,w
IFDEF SX48_52
mov w,#RD_LVL ;Setup RD CMOS or TTL levels, 0 = TTL, 1 = CMOS
mov !rd,w
mov w,#RE_LVL ;Setup RE CMOS or TTL levels, 0 = TTL, 1 = CMOS
mov !re,w
ENDIF
_mode PLP_W ;point MODE to write PLP register
mov w,#RA_PLP ;Setup RA Weak Pull-up, 0 = enabled, 1 = disabled
mov !ra,w
mov w,#RB_PLP ;Setup RB Weak Pull-up, 0 = enabled, 1 = disabled
mov !rb,w
mov w,#RC_PLP ;Setup RC Weak Pull-up, 0 = enabled, 1 = disabled
mov !rc,w
IFDEF SX48_52
mov w,#RD_PLP ;Setup RD Weak Pull-up, 0 = enabled, 1 = disabled
mov !rd,w
mov w,#RE_PLP ;Setup RE Weak Pull-up, 0 = enabled, 1 = disabled
mov !re,w
ENDIF
_mode DDIR_W ;point MODE to write DDIR register
mov w,#RA_DDIR ;Setup RA Direction register, 0 = output, 1 = input
mov !ra,w
mov w,#RB_DDIR ;Setup RB Direction register, 0 = output, 1 = input
mov !rb,w
mov w,#RC_DDIR ;Setup RC Direction register, 0 = output, 1 = input
mov !rc,w
IFDEF SX48_52
mov w,#RD_DDIR ;Setup RD Direction register, 0 = output, 1 = input
mov !rd,w
mov w,#RE_DDIR ;Setup RE Direction register, 0 = output, 1 = input
mov !re,w
ENDIF
mov w,#RA_latch ;Initialize RA data latch
mov ra,w
mov w,#RB_latch ;Initialize RB data latch
mov rb,w
mov w,#RC_latch ;Initialize RC data latch
mov rc,w
IFDEF SX48_52
mov w,#RD_latch ;Initialize RD data latch
mov rd,w
mov w,#RE_latch ;Initialize RE data latch
mov re,w
ENDIF
;------------------------------------------------------------------------------
; Clear all Data RAM locations
;------------------------------------------------------------------------------
zeroRam
IFDEF SX48_52 ;SX48/52 RAM clear routine
mov w,#$0a ;reset all ram starting at $0A
mov fsr,w
:zeroRam clr ind ;clear using indirect addressing
incsz fsr ;repeat until done
jmp :zeroRam
_bank bank0 ;clear bank 0 registers
clr $10
clr $11
clr $12
clr $13
clr $14
clr $15
clr $16
clr $17
clr $18
clr $19
clr $1a
clr $1b
clr $1c
clr $1d
clr $1e
clr $1f
ELSE ;SX18/20/28 RAM clear routine
clr fsr ;reset all ram banks
:zeroRam sb fsr.4 ;are we on low half of bank?
setb fsr.3 ;If so, don't touch regs 0-7
clr ind ;clear using indirect addressing
incsz fsr ;repeat until done
jmp :zeroRam
ENDIF
;------------------------------------------------------------------------------
; Initialize program/VP registers
;------------------------------------------------------------------------------
;VP_begin I2C Multi-Master
_bank i2cmmBank
call @i2cmmInit
;VP_end ; End cut/paste for I2C MultiMaster
;------------------------------------------------------------------------------
; Setup and enable RTCC interrupt, WREG register, RTCC/WDT prescaler
;------------------------------------------------------------------------------
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
; Virtual Peripheral Guidelines Tip:
;
; The suggested default values for the option register are:
; - Bit 7 set to 0: location $01 addresses the W register (WREG)
; - Bit 3 set to 1: Prescaler assigned to WatchDog Timer
;
; If a routine must change the value of the option register (for example, to access
; the RTCC register directly), then it should restore the default value for the
; option register before exiting.
;
;?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?!?
RTCC_ON = %10000000 ;Enables RTCC at address $01 (RTW hi)
;*WREG at address $01 (RTW lo) by default
RTCC_ID = %01000000 ;Disables RTCC edge interrupt (RTE_IE hi)
;*RTCC edge interrupt (RTE_IE lo) enabled by default
RTCC_INC_EXT = %00100000 ;Sets RTCC increment on RTCC pin transition (RTS hi)
;*RTCC increment on internal instruction (RTS lo) is default
RTCC_FE = %00010000 ;Sets RTCC to increment on falling edge (RTE_ES hi)
;*RTCC to increment on rising edge (RTE_ES lo) is default
RTCC_PS_ON = %00000000 ;Assigns prescaler to RTCC (PSA lo)
RTCC_PS_OFF = %00001000 ;Assigns prescaler to WDT (PSA hi)
PS_000 = %00000000 ;RTCC = 1:2, WDT = 1:1
PS_001 = %00000001 ;RTCC = 1:4, WDT = 1:2
PS_010 = %00000010 ;RTCC = 1:8, WDT = 1:4
PS_011 = %00000011 ;RTCC = 1:16, WDT = 1:8
PS_100 = %00000100 ;RTCC = 1:32, WDT = 1:16
PS_101 = %00000101 ;RTCC = 1:64, WDT = 1:32
PS_110 = %00000110 ;RTCC = 1:128, WDT = 1:64
PS_111 = %00000111 ;RTCC = 1:256, WDT = 1:128
OPTIONSETUP equ RTCC_ON | RTCC_PS_OFF ; the default option setup for this program.
mov w,#OPTIONSETUP ; setup option register for RTCC interrupts enabled
mov !option,w ; and prescaler assigned to WDT.
jmp @mainLoop
;------------------------------------------------------------------------------
; MAIN PROGRAM CODE
;------------------------------------------------------------------------------
mainLoop
;VP_begin I2C Multi-Master
;*****************************************************************************************
; MAIN PROGRAM CODE
; This can be changed as you like to suit your own application
; At present data is read from an EEPROM device and the data stored into the last RAM bank
;*****************************************************************************************
;*********************************************************************************
; Initialize variables...
;*********************************************************************************
_bank i2cmmBank
mov w,#i2cmmSlaveAddr ; set address of slave to read.
mov i2cmmAddress,w
_bank VARS ; clear read and write address pointers
clr i2cmmReadAdr
clr i2cmmWritePtr
;*********************************************************************************
; Read a character from EEPROM 'i2cmmAddress', at location 'i2cmmReadAdr'
;*********************************************************************************
i2cRead _bank VARS
mov w,i2cmmReadAdr
_bank i2cmmBank
mov i2cmmDataBuf,w ; load send register with data address
call @i2cmmWaitNotBusy ; wait for I2CM state machine to enter idle state
call @i2cmmSendByte ; send 'want to read' and bank addess to i2c slave
call @i2cmmWaitNotBusy ; wait for I2CM state machine to enter idle state
snb i2cmmLostArb ; if arbitration was lost then wait a while and try again
jmp iveLostArb
snb i2cmmNack ; Check for no acknowledge
jmp i2cmmGotNack ; Set lights for no Ack and try again
call @i2cmmGetByte ; Gets the byte from slave and returns it in w
snb i2cmmLostArb ; if arbitration was lost wait a while and then try again
jmp iveLostArb
snb i2cmmNack ; Check for no acknowledge
jmp i2cmmGotNack ; Set lights for no ack and try again
or w,#$00 ; check for null character, indicating end of string
snb z ; null char, end of string...restart
jmp mainLoop
mov i2cRecvChar,w ; save received character
; cjne i2cRecvChar,#'A',i2cmmBadData ; Check data received matches data saved in EEPROM
; for example store all 'A's in the EEPROM and confirm
; read data is an 'A'.
;*********************************************************************************
; Store the characters received in bank 7...
;*********************************************************************************
i2cmmStoreChar clrb i2cmmRedLed1
setb i2cmmGreenLed ; indicate data received okay
_bank VARS
mov w,#i2cmmRecvString
add w,i2cmmWritePtr
mov fsr,w
mov w,i2cRecvChar ; save revcd data to address pointed to by fsr
mov indf,w
_bank VARS
inc i2cmmReadAdr ; set to read next address
inc i2cmmWritePtr ; increment offset of where to save data
snz
jmp mainLoop ; finished reading entire EEPROM bank... Restart
jmp i2cRead ; read another character from eeprom
;*********************************************************************************
; This Master will wait here when arbitration is lost
;*********************************************************************************
iveLostArb clrb i2cmmGreenLed
snb i2cmmRedLed2 ; This master has lost arbitration
jmp i2cmmLedOn
i2cmmLedOff setb i2cmmRedLed2 ; Toggle green LED
jmp i2cmmWaitHere
i2cmmLedOn clrb i2cmmRedLed2
i2cmmWaitHere _bank i2cmmTimer ; Wait a 'random' time before trying again
test i2cmmTimerLow
sz
jmp i2cmmWaitHere
_bank i2cmmBank
clrb i2cmmLostArb
jmp mainLoop ; Retry I2C operation
;*********************************************************************************
; ERROR CONDITIONS:
;*********************************************************************************
i2cmmGotNack setb i2cmmGreenLed
setb i2cmmRedLed1
setb i2cmmRedLed2
jmp mainLoop ; Did not get an acknowledge from slave
i2cmmBadData setb i2cmmRedLed1
clrb i2cmmRedLed2
clrb i2cmmGreenLed
mov w,i2cRecvChar ; Got incorrect data from EEPROM
jmp $ ; should never occur
;VP_end ; End cut/paste for I2C MultiMaster
jmp mainLoop
;*****************************************************************************************
END ;End of program code
;*****************************************************************************************
;*****************************************************************************************
;*****************************************************************************************
;*****************************************************************************************
;*****************************************************************************************
;*****************************************************************************************
;*****************************************************************************************
| file: /Techref/scenix/lib/io/osi2/i2c/i2c_dual_multi_master.src, 84KB, , updated: 2001/10/18 11:39, local time: 2024/4/17 21:55,
3.144.10.14:LOG IN
|
| ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions? <A HREF="http://www.sxlist.com/Techref/scenix/lib/io/osi2/i2c/i2c_dual_multi_master.src"> scenix lib io osi2 i2c i2c_dual_multi_master</A> |
| Did you find what you needed? |
Welcome to sxlist.com!sales, advertizing, & kind contributors just like you! Please don't rip/copy (here's why Copies of the site on CD are available at minimal cost. |
Welcome to www.sxlist.com! |
.