please dont rip this site

1. The local PC monitors the RI (Ring Indicate) signal via software.

2. When the remote modem wants to communicate with the local modem, it generates an RI signal. This signal is transferred by the local modem to the local PC.

3. The local PC responds to the RI signal by asserting the DTR (Data Terminal Ready) signal when it is ready to communicate.

4. After recognizing the asserted DTR signal, the modem responds by asserting DSR (Data Set Ready) after it is connected to the communications line. DSR indicates to the PC that the modem is ready to exchange further control signals with the DTE to commence communication. When DSR is asserted, the PC begins monitoring DCD for indica-tion that data is being sent over the communication line.

5. The modem asserts DCD (Data Carrier Detect) after it has received a carrier signal from the remote modem that meets the suitable signal criteria.

6. At this point data transfer can began. If the local modem has full–duplex capability, the CTS (Clear to Send) and RTS (Request to Send) signals are held in the asserted state. If the modem has only half–du-plex capability, CTS and RTS provide the handshak-ing necessary for controlling the direction of the data flow. Data is transferred over the RD and TD sig-nals.

 a. Useing the letters L for low and H for high: Say you wanted to send an ASCII 'A' (01000001). This would be the sequence:

HHHHLHLLLLLHLHHHH
1   23       4

Notes:
1. The serial line idles in a high state and must be in a high state for at least 1 bit time before the start bit.
2. The start bit. Note that that it must be the opposite polarity of the idle state. It is one bit time.
3. This is the least significant bit. the other bits follow in sequence.
4. This is the stop bit. Note that it just idles the line but must be present because the line must be idle for at least 1 bit time before a start bit.

7. When the transfer of data has been completed, the PC disables the DTR signal. The modem follows by inhibiting the DSR and DCD signals. At this point the PC and modem are in the original state described in step number 1.

Questions:


file: /Techref/io/serial/seq1.htm, 3KB, , updated: 2013/2/1 18:31, local time: 2024/3/28 12:38,
TOP NEW HELP FIND: 
44.192.75.131:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://www.sxlist.com/Techref/io/serial/seq1.htm"> RS232 Sequence Example.</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

 

Welcome to sxlist.com!


Site supported by
sales, advertizing,
& kind contributors
just like you!

Please don't rip/copy
(here's why

Copies of the site on CD
are available at minimal cost.
 

Welcome to www.sxlist.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .