Code generator for Delays by Nikolai Golovchenko Wow!
Counting Hours Minutes and Seconds
PIC 16 Delay Tutorial by Vasily Koudymov
Delay Subroutines
Are there simulation problems with delays?
James Newton says:
I also wrote this god-awful macro for the Parallax SX key asembler that may be of use to someone: It produces the smallest and/or tightest loop delays inline when you call it with the value and units of time you wish to delay for; calculating the number of cycles based on the processor speed. The CpuMhz equate must be adjusted to what ever is right for your chip. It should probably be called CpuMips vice CpuMhz. The only redeming virtue is that it does not use anything other than w (on the SX you can decrement W); no stack use, no register use. :device pins28, pages1, banks8, turbo, stackx, optionx, carryx reset reset_entry CpuMhz = 50 temp ds 1 usec EQU -6 msec EQU -3 sec EQU 1 cycles EQU 0 mynop MACRO noexpand page $>>8 ENDM cyclefor MACRO 1 _cycles = \1 IF _cycles > 0 _temp = $//4 IF _temp = 2 IF _cycles <5 REPT _cycles expand mynop noexpand ENDR _cycles = 0 ELSE expand mynop noexpand _cycles = _cycles -1 ENDIF ENDIF IF _temp = 1 IF _cycles < 6 REPT _cycles expand mynop noexpand ENDR _cycles = 0 ELSE expand mynop mynop noexpand _cycles = _cycles -2 ENDIF ENDIF IF _cycles > 3 expand mov w, #_cycles / 3 decsz 1 ;dec w clrb 2.1 ;modify PC to jump back noexpand _cycles = _cycles // 3 ;cycles left over ENDIF IF _cycles > 0 REPT _cycles expand mynop noexpand ENDR ENDIF ENDIF ENDM reset_entry mov w,#$7F mov !OPTION,w delayhelp MACRO ERROR 'USAGE: delay value, [usec,msec,sec,cycles]' ENDM delay MACRO 2 noexpand IF (\2=usec OR \2=msec OR \2=sec) AND (\1<1000 AND \1>0) IF \2=sec _cycles = (\1 * 1000000 / (1000/CpuMhz)) ENDIF IF \2=msec _cycles = (\1 * 1000 / (1000/CpuMhz)) ENDIF IF \2=usec _cycles = (\1 / (1000/CpuMhz)) ENDIF IF \2=cycles _cycles = \2 ENDIF IF _cycles = 0 expand ;delay less than one cycle at this processor speed' noexpand ELSE IF _cycles > 255 REPT (_cycles / 256) cyclefor 256 _cycles = _cycles - 256 ENDR ENDIF cyclefor _cycles ENDIF ELSE delayhelp ENDIF ENDM delay 999, usec delay 200, usec delay 250, usec delay 10, usec delay 20, usec delay 100, msec
See Also:
See:
Archive:
Questions:
Code:
try this for 1 to 117million cycle delay delay macro Cycles variable CyclesLeft ,LoopCycles,d_used ; Keep Track of Remaining Cycle local iloop CyclesLeft = Cycles if CyclesLeft > .327680 ; 0x5 * 0xffff d_used = 3 else if Cycles > 3*0xFF d_used = 2 else d_used = 1 endif endif if d_used == 3 LoopCycles = (Cycles-6-.10) / 7 CyclesLeft = (Cycles-6-.10) - (LoopCycles*7) endif if d_used == 2 LoopCycles = (Cycles-4-6) / 5 CyclesLeft = (Cycles-4-6) - (LoopCycles*5) endif if Cycles >=5 if d_used == 1 LoopCycles = (Cycles-2-2) / 3 CyclesLeft = (Cycles-2-2) - (LoopCycles*3) endif movlw (LoopCycles & 0xFF)+1 movwf STACK-0 if d_used >=2 movlw ((LoopCycles>>8) & 0xFF)+1 movwf STACK-1 endif if d_used >=3 if ((LoopCycles>>.16) > .255 ) error "Required Delay is longer than 'delay' Macro can support" endif movlw ((LoopCycles>>.16) & 0xFF)+1 movwf STACK-2 endif iloop if d_used >=3 goto $+1 endif if d_used >=2 goto $+1 endif decfsz STACK-0,F goto iloop if d_used >=2 decfsz STACK-1,F goto iloop+1 endif if d_used >=3 decfsz STACK-2,F goto iloop+2 endif endif while CyclesLeft >= 2 ; Put in 2 Instruction Cycle Delays goto $ + 1 CyclesLeft = CyclesLeft - 2 endw if CyclesLeft == 1 ; Put in the Last Required Cycle nop endif endm+
Comments:
file: /Techref/microchip/delays.htm, 7KB, , updated: 2021/5/6 13:34, local time: 2024/12/3 03:03,
18.97.14.87:LOG IN
|
©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions? <A HREF="http://www.sxlist.com/TECHREF/microchip/delays.htm"> PIC Microcontoller Time Method </A> |
Did you find what you needed? |
Welcome to sxlist.com!sales, advertizing, & kind contributors just like you! Please don't rip/copy (here's why Copies of the site on CD are available at minimal cost. |
Welcome to www.sxlist.com! |
.